


Medical displays specialize in reproducing clear images with high brightness and contrast while maintaining color accuracy. In recent years, there has been a push for smaller and thinner displays in the LCD and LED panel market. In addition, increased performance and image quality has increased heat generation. Therefore,...
Published: Jul 18, 2018



SANYO DENKI newly developed and released the 97 × 33 mm blower San Ace B97 9BMC type (hereinafter “new model”) which achieves the highest cooling performance in the industry*. This paper provides a detailed introduction of this new product.
Download to find out more.
Published: Jul 17, 2018



In the case of AC/DC power units, it is not dramatic technology breakthroughs that drive the trend, it is good engineering and the inventiveness to combine the best of a whole range of techniques and technologies that separate a really innovative power supply from an average one.
This article looks at AC/DC power...
Published: Jul 23, 2018



When transitioning from a traditional phone network to a voice over IP (VoIP) network, it is essential to recognize a key difference between the public switched telephone network (PSTN) and the private data network that will be called upon to take its place.
The PSTN is connected to a massive battery array that allows...
Published: Jul 25, 2018



Racks organize IT equipment, such as servers and network switches, into standardized assemblies that make efficient use of space and other resources. Depending on the options you choose, they can also improve power protection, cooling, cable management, device management, physical security, mobility, ease of installation...
Published: Jul 25, 2018



In this white paper eGaN FET technology is applied in a high frequency resonant converter. Previously, the advantages provided by eGaN FETs in hard switching isolated and non-isolated applications were addressed.
This paper will demonstrate the ability of the eGaN FET to improve efficiency and output power density...
Published: Jul 24, 2018



If you supply products for GSA Schedules and other government contracts, those products must comply with the federal Trade Agreements Act (TAA). Failure to comply with TAA can lead to bid award cancellation, multimillion-dollar fines and exclusion from federal contracting.
Sourcing TAA-compliant IT products presents...
Published: Jul 25, 2018



This paper describes a new two-phase cooling heat transfer cell based on a submerged vibration-induced bubble ejection process in which small vapor bubbles attached to a solid surface are dislodged and propelled into the cooler bulk liquid. This ejection technique involves forcibly removing the attached vapor bubbles with...
Published: Jul 20, 2018



Little doubt exists about contemporary battery power and its diverse use potential. With the advent of lighter, smaller, higher powered, lower amperage cells, the technological applications have become “understandably” broad. Significantly, the use of portable medical devices which are battery-powered, has...
Published: Jul 25, 2018



Two key factors in maximizing power converter performance and successful power system design are thermal environment and heat management. Power densities are increasing faster than power converter efficiency; thus increased performance from thermal management solutions is required.
Products based on Vicor’s...
Published: Jul 24, 2018



The drive for smaller power supplies goes handin hand with a need for greater efficiency. There’ s a direct relationship here because the smaller the power unit, the smaller the area available for dissipating heat through conduction and convection. Through both measurement and calculation, XP Power has developed...
Published: Jul 23, 2018



XP Power offers advice on power supply design, which could help with your next design. Most electronics engineers can design an AC/DC power supply based on first principles but it’s through careful refinements in the design that real reliability and efficiency improvements appear.
In this whitepaper, XP Power...
Published: Jul 23, 2018



Power has always been a design consideration. Traditionally, though, a lower priority has been assigned to power than to most other variables (speed/performance, cost, time-to-market, risk, etc.). In today’s marketplace, however, power has become a very important component in the designer’s decision making...
Published: Jul 19, 2018



The rapidly growing number of electric vehicles (EVs) on the road requires more charging infrastructures to top off energy so that EVs can get back on road quickly. An EV charging station is an important element in the charging infrastructure, which supplies electric energy to the EV and provides a network connection....
Published: Jul 17, 2018